The dominant property of building envelope fabric which contributes significantly to minimize electricity utilization in building is the thermo-physical properties. There is inadequate literature on representative practical data of thermo-physical properties of the dominant building envelope components in Ghana. This study aims to use cost-effective approach to characterize the thermo-physical properties of only cement-based mortar and concrete blocks used in Ghana for building components specifically wall design. Mixed methods research design was employed to achieving the aim. A questionnaire survey was used among sampled building fabric components manufacturers to pick representative data on thermos-physical properties of their mortar and concrete blocks. Also, an experimental procedure employing a transient technique with a TCi Thermal Analyser was used to determine the thermo-physical properties of selected mortar and concrete blocks from Ghana in addition to designed parametric mortar and concrete blocks with varied ratios obtained from the survey were undertaken at University of Nottingham. From the study, a trend of decreasing thermal conductivity and thermal effusivity with corresponding decreasing sand content was observed with all the different sand types. The thermal conductivities of both mortar and concrete parametric blocks meet the range of expected standard values outlined in Chattered Institute of Building Services Engineers (CIBSE) Guide A. The major limitation of the work is the dimension of the sample size; which is not inconsistent with standard block size due to the experimental setup used. It is expected that, the characterization of the predominant cement-based building fabrics components will contribute to improved building performance analysis with significant savings in electricity utilization for space cooling.
References
[1]
Mohamed, A., Hasan, A. and Sirén, K. (2014) Fulfillment of Net-Zero Energy Building (NZEB) with Four Metrics in a Single Family House with Different Heating Alternatives. Applied Energy, 114, 385-399. https://doi.org/10.1016/j.apenergy.2013.09.065
[2]
Baetens, R., De Coninck, R., Van Roy, J., Verbruggen, B., Driesen, J. and Helsen, L. (2012) Assessing Electrical Bottlenecks at Feeder Level for Residential Net Zero-Energy Buildings by Integrated System Simulation. Applied Energy, 96, 74-83. https://doi.org/10.1016/j.apenergy.2011.12.098
[3]
Fong, K.F. and Lee, C.K. (2012) Towards Net Zero Energy Design for Low-Rise Residential Buildings in Subtropical Hong Kong. Applied Energy, 93, 686-694. https://doi.org/10.1016/j.apenergy.2012.01.006
[4]
Leckner, M. and Zmeureanu, R. (2011) Life Cycle Cost and Energy Analysis of a Net Zero Energy House with Solar Combisystem. Applied Energy, 88, 232-241. https://doi.org/10.1016/j.apenergy.2010.07.031
[5]
Becchio, C., Corgnati, S.P., Monetti, V. and Fabrizio, E. (2014) From High Performing Buildings to Nearly Zero Energy Buildings: Potential of an Existing Office Building. In: Arisoy, P.D.A., Ed., Climamed 13 Proceedings Mediterranean Congress of Climatalization Proceedings Book, Turkish Society of HVAC and Sanitary Engineers, Istanbul, 72-81.
[6]
Santamouris, M. and Kolokotsa, D. (2013) Passive Cooling Dissipation Techniques for Buildings and Other Structures: The State of the Art. Energy and Buildings, 57, 74-94. https://doi.org/10.1016/j.enbuild.2012.11.002
[7]
Anais, J., Regis, O. and Xavier, P. (2013) Selection Criteria of Thermal Mass Materials for Low Energy Building Construction Applied to Conventional and Alternative Materials. Energy and Buildings, 63, 36-48. https://doi.org/10.1016/j.enbuild.2013.03.047
[8]
Yu, R., Spiesz, P. and Brouwers, H.J.H. (2015) Development of an Eco-Friendly Ultra-High Performance Concrete (UHPC) with Efficient Cement and Mineral Admixtures Uses. Cement and Concrete Composites, 55, 383-394. https://doi.org/10.1016/j.cemconcomp.2014.09.024
[9]
Chabannes, M., Benezet, J.-C., Clerc, L. and Garcia-Diaz, E. (2014) Use of Raw Rice Husk as Natural Aggregate in a Lightweight Insulating Concrete: An Innovative Application. Construction and Building Materials, 70, 428-438. https://doi.org/10.1016/j.conbuildmat.2014.07.025
[10]
Amos-Abanyie, S., Akuffo, F.O. and Kuting-Sanwu, V. (2013) Effects of Thermal Mass,Window Size and Night-Time Ventilation on Peak Indoor Air Temperature in the Warm-Humid Climate of Ghana. The Scientific World, 9, Article ID: 621095. https://doi.org/10.1155/2013/621095
[11]
Kendrick, C., Ogden, R., Wang, X. and Baiche, B. (2012) Thermal Mass in New Build UK Housing: A Comparison of Structural Systems in a Future Weather Scenario. Energy and Buildings, 48, 40-49. https://doi.org/10.1016/j.enbuild.2012.01.009
[12]
Sadineni, S.B., Madala, S. and Boehm, R.F. (2011) Passive Building Energy Savings: A Review of Building Envelope Components. Renewable and Sustainable Energy Review, 15, 3617-3631. https://doi.org/10.1016/j.rser.2011.07.014
[13]
Koranteng, C. (2010) Energy Performance of Office Buildings in Ghana. Journal of Science and Technology, 30, 114-127. https://doi.org/10.4314/just.v30i2.60542
[14]
Radhi, H. (2009) Can Envelope Codes Reduce Electricity and CO2 Emissions in Different Types of Buildings in the Hot Climate of Bahrain. Energy, 34, 205-215. https://doi.org/10.1016/j.energy.2008.12.006
[15]
Iwaro, J. and Mwasha, A. (2010) A Review of Building Energy Regulation and Policy for Energy Conversation in Developing Countries. Energy Policy, 38, 7744-7755. https://doi.org/10.1016/j.enpol.2010.08.027
[16]
Givoni, B. (2011) Indoor Temperature Reduction by Passive Cooling Systems. Solar Energy, 85, 1692-1726. https://doi.org/10.1016/j.solener.2009.10.003
[17]
Escriva-Escriva, G. (2011) Basis Actions to Improve Energy Efficiency in Commercial Buildings in Operation. Energy and Building, 43, 3106-3111. https://doi.org/10.1016/j.enbuild.2011.08.006
[18]
Darkwa, J., Su, O. and Zhou, T. (2012) Development of Non-Deform Micro-En- capsulated Phase Change Energy Storage Tablets. Applied Energy, 98, 441-447. https://doi.org/10.1016/j.apenergy.2012.04.006
[19]
Ballarini, I. and Corrado, V. (2012) Analysis of the Building Energy Balance to Investigate the Effect of Thermal Insulation in Summer Conditions. Energy and Buildings, 52, 168-180. https://doi.org/10.1016/j.enbuild.2012.06.004
[20]
Buker, M.S., Mempouo, B. and Riffat, S.B. (2015) Experimental Investigation of a Building Integrated Photovoltaic/Thermal Roof Collector Combined with a Liquid Desiccant Enhanced Indirect Evaporative Cooling System. Energy Conversion and Management, 101, 239-254. https://doi.org/10.1016/j.enconman.2015.05.026
[21]
Adjei, E., Omer, S. and Wu, Y.P. (2015) Potential Integration of Sustainable Technology in Office Building in Ghana: Exploratory Study. 14th International Conference on Sustainable Energy Technologies-SET, Nottingham, UK, 25-27 August 2015.
[22]
Oppong, R.A. and Badu, E. (2012) Building Material Preferences in Warm-Humid and Hot-Dry Climates in Ghana. Journal of Science and Technology, 32, 24-37. https://doi.org/10.4314/just.v32i3.4
[23]
Laaroussi, N., Cherki, A., Garoum, M., Khabbazi, A. and Feiz, A. (2013) Thermal Properties of a Sample Prepared Using Mixtures of Clay Bricks. Energy Procedia, 42, 337-346. https://doi.org/10.1016/j.egypro.2013.11.034
[24]
Gyimah, K.A. (2019) Windows for Quality Indoor Environment: A Case of Offices in the Warm-Humid Climate of Kumasi, Ghana. PhD Thesis, Department of Architecture, KNUST, Kumasi.
[25]
Simons, B. (2015) Simulation-Based Exploration of the Thermal Performance of some Multi Storey Office Buildings in Accra, Ghana. PhD Thesis, Department of Building Technology, KNUST, Kumasi.
[26]
Rübner, K. and Hoffmann, D. (2006) Characterization of Mineral Building Materials by Mercury-Intrusion Porosimetry. Particle & Particle Systems Characterization, 23, 20-28. https://doi.org/10.1002/ppsc.200601008
[27]
ISO 8302 (1991) Thermal Insulation-Determination of Steady-State Thermal Resistance and Related Properties-Guarded Hot Plate Apparatus.
[28]
ASTM C177-04 (2004) Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus. ASTM International, West Conshohocken, PA. https://www.astm.org
[29]
ASTM D7984-16 (2016) Standard Test Method for Measurement of Thermal Effusivity of Fabrics Using a Modified Transient Plane Source (MTPS) Instrument. ASTM International, West Conshohocken, PA. https://www.astm.org
BS 1199 and 1200 (1976) Specifications for Building Sands from Natural Sources.
[32]
ASTM C33, Standard Specification for Concrete Aggregates.
[33]
BS EN 12390-1 (2012) Testing Hardened Concrete. Shape, Dimensions and Other Requirements for Specimens and Moulds.
[34]
BS EN 12390-2 (2009) Testing Hardened Concrete. Making and Curing Specimens for Strength Tests STANDARD. British-Adopted European Standard.
[35]
BS EN 1367-4 (2008) Tests for Thermal and Weathering Properties of Aggregates. Determination of Drying Shrinkage STANDARD. British-Adopted European Standard.
[36]
Bahar, R., Benazzoug, M. and Kenai, S. (2004) Performance of Compacted Cement Stabilized Soil. Cement and Concrete Composites, 25, 633-641. https://doi.org/10.1016/S0958-9465(02)00077-X
[37]
Akinmusuru, J.O. (1995) Thermal Conductivity of Earth Blocks. Journal of Materials in Civil Engineering, 6, 341-351. https://doi.org/10.1061/(ASCE)0899-1561(1994)6:3(341)
[38]
Reddy Venkatarama, B.V. and Gupta, A. (2006) Tensile Bond Strength of Soil-Cement Block Masonry Couplets Using Cement-Soil Mortars. Journal of Materials in Civil Engineering, 18, 36-45. https://doi.org/10.1061/(ASCE)0899-1561(2006)18:1(36)
[39]
Milon, K.H., Rashid, M.H., Debashis, M. and Tozammel, H. (2012) Effects of Aggregate Types on Thermal Properties of Concrete. ARPN Journal of Engineering and Applied Sciences, 7, 900-907.
