|
|
- 2019
短切碳纤维/乙烯基酯树脂片状模塑料拉伸性能的有限元模拟
|
Abstract:
采用Python语言对ABAQUS软件进行二次开发，生成了短切碳纤维在乙烯基酯树脂中随机分布的二维平面应变模型，建立代表性体积单元（RVE），通过Hypermesh对模型进行网格划分，为保证RVE应力场的均匀协调性，在周期性边界条件下，对短切碳纤维/乙烯基树脂进行拉伸性能数值模拟计算分析，并结合实验研究了短切碳纤维长度对片状模塑料拉伸性能的影响。结果验证了对短切碳纤维/乙烯基树脂片状模塑料拉伸模量随纤维长度的增大出现先增大后变缓的趋势，表明利用Python-ABAQUS建立二维平面应变RVE模型的合理性。本研究为短切碳纤维/乙烯基树脂片状模塑料在汽车轻量化行业的应用提供了理论及实验依据。 Python language was used to redevelop ABAQUS to generate 2D plane strain model with randomly distributed chopped carbon fibers. The representative volume element(RVE) was created and meshed with Hypermesh. In order to ensure the uniform coordination of the stress field of the RVE, the numerical simulation analysis of the tensile properties was under periodic boundary conditions, and the change trend of the effect of fiber length on the elastic modulus of the sheet molding compound was studied. The results verify that the tensile modulus of chopped carbon fiber/vinyl ester resin sheet molding compounds increases first and then decreases gradually with the increase of fiber length, and it is right to use Python-ABAQUS to establish a 2D plane strain RVE model. This study provides theoretical and experimental basis for the application of sheet molding compound in the automotive lightmass industry
| [1] | ZHANG J T, LIU L S, ZHAI P C. The prediction of the dynamic responses of ceramic particle reinforced MMCs by using multi-particle computational micro-mechanical method[J]. Composites Science & Technology, 2007, 67(13):2775-2785. |
| [2] | 尚士朋. 基于商业有限元软件的周期性材料等效性能预测均匀化实施新方法[D]. 大连:大连理工大学, 2016.SHANG Shipeng. The novel implementation of asymptotic homogenization periodic the effective properties of periodic materials based on commercial FEA software[D]. Dalian:Dalian University of Technology, 2016(in Chinese). |
| [3] | 张超, 许希武, 严雪. 纺织复合材料细观力学分析的一般性周期性边界条件及其有限元实现[J]. 航空学报, 2013, 34(7):1636-1645. ZHANG Chao, XU Xiwu, YAN Xue. General periodic boundary conditions and their application to micromechanical finite element analysis of textile composites[J]. Acta Aeronautica et Astronautica Sinica, 2013, 34(7):1636-1645(in Chinese). |
| [4] | MOHAMMAD I, TUDRYN G J, PICU C R. Microstruc ture modeling of random composites with cylindrical inclusions having high volume fraction and broad aspect ratio distribution[J]. Computational Materials Science, 2016, 125:309-318. |
| [5] | PAlENCIA J C G, SAKAMAKI T, ARAKI M, et al. Impact of powertrain electrification, vehicle size reduction and lightweight materials substitution on energy use, CO2 emissions and cost of a passenger light-duty vehicle fleet[J]. Energy, 2015, 93:1489-1504. |
| [6] | 赵玉梅. 汽车轻量化用改性聚丙烯的研究进展[J]. 合成树脂及塑料, 2016, 33(6):91-94.ZHAO Yumei. Research progress of modified PP for auto mobile lightweight[J]. China Synthetic Resin & Plastics, 2016, 33(6):91-94(in Chinese). |
| [7] | 刘强, 马小康, 宗志坚. 斜纹机织碳纤维/环氧树脂复合材料性能及其在电动汽车轻量化设计中的应用[J]. 复合材料学报, 2011, 28(5):83-88.LIU Qiang, MA Xiaokang, ZONG Zhijian. Properties of twill-weave carbon fabric/epoxy composites and its application on light-weight design for electric vehicles[J]. Acta Materiae Compositae Sinica, 2011, 28(5):83-88(in Chinese). |
| [8] | 罗益峰. 汽车用新材料的最新进展——轻量、节能和环保[J]. 纺织导报, 2017(3):39-43.LUO Yifeng. Latest trends in automobile materials development:Light-weighting, energy-saving and environment-friendly[J]. China Textile Leader, 2017(3):39-43(in Chinese). |
| [9] | WULFSBERG J, HERRMANN A, ZIEGMANN G, et al. Combination of carbon fibre sheet moulding compound and prepreg compression moulding in aerospace industry[J]. Procedia Engineering, 2014, 81:1601-1607. |
| [10] | RAHMAN A, PANIGRAHI S, KUSHWAHA R L, et al. Effect of fiber diameter on properties of compression molded flax fiber-reinforced biocomposites[J]. International Journal of Composite Materials, 2013, 2013(5):122-129. |
| [11] | 李建. 模压成型纤维增强环氧片状模塑料的研究[D]. 武汉:武汉理工大学, 2009.LI Jian. Study on fiber reinforced epoxy sheet molding compound[D]. Wuhan:Wuhan University of Technology, 2009(in Chinese). |
| [12] | BOYLAN S, CASTRO J M. Effect of reinforcement type and length on physical properties, surface quality, and cycle time for sheet molding compound(SMC) compression molded parts[J]. Journal of Applied Polymer Science, 2010, 90(9):2557-2577. |
| [13] | 蔡烨梦. 乙烯基酯树脂用碳纤维乳液上浆剂的制备与性能研究[D]. 哈尔滨:哈尔滨工业大学, 2017.CAI Yemeng. Preparation and properties of carbon fiber emulsion sizing agent for vinyl ester resin[D]. Harbin:Harbin Institute of Technology, 2017(in Chinese). |
| [14] | 中国国家标准化管理委员会. 纤维增强塑料拉伸性能试验方法:GB/T 1447-2005[S]. 北京:中国标准出版社, 2005.Standardization Administration of the People's Republic of China. Fiber-reinforced plastics composites-Determination of tensile properties:GB/T 1447-2005[S]. Beijing:China Standards Press, 2005(in Chinese). |
| [15] | 曹东风. 细观特征对SiCp/Al复合材料力学行为影响的实验及数值研究[D]. 武汉:武汉理工大学, 2011.CAO Dongfeng. Experimental and numerical studies on effect of meso-scale characterization on mechanical behaviors of SiCp/A1 composites[D]. Wuhan:Wuhan University of Technology, 2011(in Chinese). |
| [16] | BORBELY A, BIERMANN H. Finite element investi gation of the effect of particle distribution on the uniaxial stress-strain behavior of particulate-reinforced metal-matrix compo-sites[J]. Materials Science & Engineering A, 2001, 313(1):34-45. |
| [17] | 章继峰, 王振清, 周健生, 等. 基于Python-Abaqus复合材料代表性体积元的数值模型[J]. 宇航材料工艺, 2009, 39(3):25-29.ZHANG Jifeng, WANG Zhenqing, ZHOU Jiansheng, et al. Numerical modeling of composite representative volume element(RVE) based on Python-Abaqus[J]. Aerospace Materials & Technology, 2009, 39(3):25-29(in Chinese). |
| [18] | LIU H, ZENG D, LI Y, et al. Development of RVE-embedded solid elements model for predicting effective elastic constants of discontinuous fiber reinforced composites[J]. Mechanics of Materials, 2016, 93:109-123. |
| [19] | LU Z, YUAN Z, LIU Q. 3D numerical simulation for the elastic properties of random fiber composites with a wide range of fiber aspect ratios[J]. Computational Materials Science, 2014, 90(1):123-129. |
| [20] | 焦文文. 基于周期性边界条件的颗粒增强金属基复合材料棘轮行为的数值模拟[D]. 成都:西南交通大学, 2011.JIAO Wenwen. Numerical simulation for ratcheting of particle reinforced metal matrix composites based on periodical boundary condition[D]. Chengdu:Southwest Jiaotong University, 2011(in Chinese). |
