全部 标题 作者
关键词 摘要

OALib Journal期刊
ISSN: 2333-9721
费用:99美元

查看量下载量

相关文章

更多...

Preparation and Properties of the Composite Enhancement Layer of Bearing Ring

DOI: 10.4236/wjm.2020.1010010, PP. 139-153

Keywords: Strengthen Grinding Treatment, Conventional Treatment, Composite Enhancement Layer, Running Reliability

Full-Text   Cite this paper   Add to My Lib

Abstract:

In this paper, the NU308 bearing rings were subjected to strengthen grinding treatment (SGT) at ambient temperature. And the running reliabilities of specimens that subjected to SGT and conventional treatment (CT) were respectively investigated by testing dynamic properties including the running temperature, vibrations, and surface burning. Moreover, the residual stress, microtopography, and microstructures on the cross-section were respectively tested with residual stress analyzer and field-emission scanning electron microscopy. The results showed that the running reliabilities of the specimen after SGT had been significantly improved with the reduction of running temperature, vibration, and surface burning. Further study showed that the specimen’s surface was filled with disordered micropores after SGT compared to the regular strip texture on the CT specimen’s surface, and the maximum residual compressive stress induced by SGT was about ?900 MPa. Moreover, the thickness of the residual compressive stress layer was over 180 μm, while the thickness of severe plastic deformation layer was about 50 μm.

References

[1]  Schuhler, G., Jourani, A., Bouvier, S. and Perrochat, J.M. (2018) Efficacy of Coatings and Thermochemical Treatments to Improve Wear Resistance of Axial Piston Pumps. Tribology International, 126, 376-385.
https://doi.org/10.1016/j.triboint.2018.05.007
[2]  Gheisari, R. and Polycarpou, A.A. (2018) Three-Body Abrasive Wear of Hard Coatings: Effects of Hardness and Roughness. Thin Solid Films, 666, 66-75.
https://doi.org/10.1016/j.tsf.2018.07.052
[3]  Trdan, U, Skarba, M, Porro, J.A., Ocaña, J.L. and Grum, J. (2018) Application of Massive Laser Shock Processing for Improvement of Mechanical and Tribological Properties. Surface & Coatings Technology, 342, 1-11.
https://doi.org/10.1016/j.surfcoat.2018.02.084
[4]  Wang, X., Xia, W.G., Wu, X.Q., Wei, Y.P. and Huang, C.G. (2013) Microstructure and Mechanical Properties of an Austenite NiTi Shape Memory Alloy Treated with Laser Induced Shock. Materials Science and Engineering: A, 578, 1-5.
https://doi.org/10.1016/j.msea.2013.04.058
[5]  Spadaro, L., Hereñú, S., Strubbia, R., Gómez Rosas, G., Bolmaro, R. and Rubio González, C. (2020) Effects of Laser Shock Processing and Shot Peening on 253 MA Austenitic Stainless Steel and Their Consequences on Fatigue Properties. Optics & Laser Technology, 122, Article ID: 105892.
https://doi.org/10.1016/j.optlastec.2019.105892
[6]  Wang, C., Shen, X.J., An, Z.B., Zhou, L.C. and Chai, Y. (2016) Effects of Laser Shock Processing on Microstructure and Mechanical Properties of K403 Nickel-Alloy. Materials & Design, 89, 582-588.
https://doi.org/10.1016/j.matdes.2015.10.022
[7]  Zhao, X.H., Zhou, H.Y. and Liu, Y. (2018) Effect of Shot Peening on the Fatigue Properties of Nickel-Based Superalloy GH4169 at High Temperature. Results in Physics, 11, 452-460.
https://doi.org/10.1016/j.rinp.2018.09.047
[8]  Klotz, T., Delbergue, D., Bocher, P., Lévesque, M. and Brochu, M. (2018) Surface Characteristics and Fatigue Behavior of Shot Peened Inconel 718. International Journal of Fatigue, 110, 10-21.
https://doi.org/10.1016/j.ijfatigue.2018.01.005
[9]  Mutter, M., Mauer, G., Mücke, R., Guillon, O. and Vaßen, R. (2017) Correlation of Splat Morphologies with Porosity and Residual Stress in Plasma-Sprayed YSZ Coatings. Surface & Coatings Technology, 318, 157-169.
https://doi.org/10.1016/j.surfcoat.2016.12.061
[10]  Huang, S., Zhou, J.Z., Du, J.J., Sun, Y.Q. and Li, M.X. (2008) Visual Study on Surface Micro-Topography and Residual Stress of Sheet Metal after Pulsed Laser Peening. Key Engineering Materials, 3, 334-337.
https://doi.org/10.4028/www.scientific.net/KEM.373-374.334
[11]  Liu, X.C., Xie, X.C., Zhang, C., et al. (2019) Effect of Micro-Dimples on Bearing Friction Performance in Strengthen Grinding. Tool Technology, 53, 28-30. (In Chinese)
[12]  Xiao, J.R., Liu, X.C., Liang, Z.W., et al. (2018) Effect of Steel Bead’s Damage on the Surface Roughness and Hardness of Bearing Rings under Strengthen Grinding Processing. Surface Technology, 47, 290-295.
[13]  Fu, L.H., Han, W., Zhao, L., Gong, K., et al. (2018) Effects of Cr3C2Content and Temperature on Sliding Friction and Wear Behaviors of Cr3C2/Ni3Al Composite Materials. Wear, 11, 163-173.
https://doi.org/10.1016/j.wear.2018.08.013
[14]  Ahmadi, A., Sadeghi, F. and Shaffer, S. (2018) In-Situ Friction and Fretting Wear Measurements of Inconel 617 at Elevated Temperatures. Wear, 9, 110-118.
https://doi.org/10.1016/j.wear.2018.06.007
[15]  Huang, Y.T., Zhou, X.L., Hua, N.B., Que, W.M. and Chen, W.Z. (2018) High Temperature Friction and Wear Behavior of Tungsten-Copper Alloys. International Journal of Refractory Metals and Hard Materials, 77, 105-112.
https://doi.org/10.1016/j.ijrmhm.2018.08.001
[16]  Mo, J.L., Wang, Z.G. and Chen, G.X. (2013) The Effect of Groove-Textured Surface on Friction and Wear and Friction-Induced Vibration and Noise. Wear, 301, 671-681.
https://doi.org/10.1016/j.wear.2013.01.082
[17]  Wang, H.J., Liu, Z.L., Zou, L. and Yang, J. (2017) Influence of Both Friction and Wear on the Vibration of Marine Water Lubricated Rubber Bearing. Wear, 4, 920-930.
https://doi.org/10.1016/j.wear.2017.02.006
[18]  Li, H.Y., Sun, H.L., Bowen, P. and Knott, J.F (2018) Effects of Compressive Residual Stress on Short Fatigue Crack Growth in a Nickel-Based Superalloy. International Journal of Fatigue, 108, 53-61.
https://doi.org/10.1016/j.ijfatigue.2017.11.010
[19]  Choi, Y. (2009) A Study on the Effects of Machining-Induced Residual Stress on Rolling Contact Fatigue. International Journal of Fatigue, 31, 1517-1523.
https://doi.org/10.1016/j.ijfatigue.2009.05.001
[20]  Ding, K.Y., Guo, Y.F. and Zou, H. (2017) Effect of Residual Stress on Bending Fatigue Behavior of Inconel 718 Coated with WC-17Co. Rare Metal Materials and Engineering, 46, 307-311.
https://doi.org/10.1016/S1875-5372(17)30085-1
[21]  Valiorgue, F., Zmelty, V., Dumas, M., Chomienne, V., Verdu, C., Lefebvre, F. and Rech, J. (2018) Influence of Residual Stress Profile and Surface Microstructure on Fatigue Life of a 15-5PH. Procedia Engineering, 23, 623-629.
https://doi.org/10.1016/j.proeng.2018.02.058
[22]  Kattoura, M., Ramaiah, S.M., Qian, D. and Vasudevan, V.K. (2018) Effect of Ultrasonic Nanocrystal Surface Modification on Elevated Temperature Residual Stress, Microstructure, and Fatigue Behavior of ATI 718Plus Alloy. International Journal of Fatigue, 110, 186-196.
https://doi.org/10.1016/j.ijfatigue.2018.01.017
[23]  Mellouli, D., Haddar, N., Köster, A. and Ayedi, H.F. (2014) Hardness Effect on Thermal Fatigue Damage of Hot-Working Tool Steel. Engineering Failure Analysis, 45, 85-95.
https://doi.org/10.1016/j.engfailanal.2014.06.007
[24]  Vrcek, A., Hultqvist, T., Baubet, Y., Björling, M., Marklund, P. And Larsson, R. (2018) Micro-Pitting and Wear Assessment of Engine Oils Operating under Boundary Lubrication Conditions. Tribology International, 129, 338-346.
https://doi.org/10.1016/j.triboint.2018.08.032
[25]  Zapletal, T., Sperka, P., Krupka, I. and Hartl, M. (2018) the Effect of Surface Roughness on Friction and Film Thickness in Transition from EHL to Mixed Lubrication. Tribology International, 128, 237-243.
https://doi.org/10.1016/j.triboint.2018.07.047
[26]  Guegan J, Kadiric A, Gabelli A and Spikes H (2016) the Relationship between Friction and Film Thickness in EHD Point Contacts in the Presence of Longitudinal Roughness. Tribology Letters, 64, Article No. 33.
https://doi.org/10.1007/s11249-016-0768-6
[27]  Liu, D.R., Yan, B., Shen, B., Liu, L. and Hu, W.B. (2018) Friction Behaviors of Rough Chromium Surfaces under Starving Lubrication Conditions. Applied Surface Science, 427, 857-862.
[28]  Fricke, S., Hager, C., Solovyev, S., Wangenheim, M. and Wallaschek, J. (2018) Influence of Surface Form Deviations on Friction in Mixed Lubrication. Tribology International, 118, 491-499.
https://doi.org/10.1016/j.triboint.2017.05.032
[29]  Volchok, A., Halperin, G. and Etsion, I. (2002) The Effect of Surface Regular Microtopography on Fretting Fatigue Life. Wear, 253, 509-515.
https://doi.org/10.1016/S0043-1648(02)00148-5
[30]  Chen, X., Han, Z., Li, X.Y. and Lu, K. (2016) Lowering Coefficient of Friction in Cu Alloys with Stable Gradient Nanostructures. Science Advances, 2, e1601942.
https://doi.org/10.1126/sciadv.1601942
[31]  Zuo, J.R., Hou, L.G., Shi, J.T., Cui, H., Zhuang, L.Z. and Zhang, J.S. (2017) the Mechanism of Grain Refinement and Plasticity Enhancement by an Improved Thermomechanical Treatment of 7055 Al Alloy. Materials Science and Engineering: A, 702, 42-52.
https://doi.org/10.1016/j.msea.2017.06.106
[32]  Liu, R., Tian, Y.Z., Zhang, Z.J., Zhang, P. and Zhang, Z.F. (2017) Fatigue Strength Plateau Induced by Microstructure Inhomogeneity. Materials Science and Engineering: A, 702, 259-264.
https://doi.org/10.1016/j.msea.2017.07.026
[33]  Shukla, S., Wang, T.H., Cotton, S. and Mishra, R.S. (2018) Hierarchical Microstructure for Improved Fatigue Properties in a Eutectic High Entropy Alloy. Scripta Materialia, 156, 105-109.
https://doi.org/10.1016/j.scriptamat.2018.07.022
[34]  Wu, P.F., Deng, Y.L., Zhang, J., Fan, S.T. and Zhang, X.M. (2018) The Effect of Inhomogeneous Microstructures on Strength and Fatigue Properties of an Al-Cu-Li Thick Plate. Materials Science and Engineering: A, 731, 1-11.
https://doi.org/10.1016/j.msea.2018.06.033

Full-Text

comments powered by Disqus

Contact Us

service@oalib.com

QQ:3279437679

WhatsApp +8615387084133