全部 标题 作者
关键词 摘要

OALib Journal期刊
ISSN: 2333-9721
费用:99美元

查看量下载量

相关文章

更多...

具有多样性混合单元的分离重组微混合器的优化设计与数值分析
Optimized Design and Numerical Analysis of a Split and Recombination Micromixer with Diverse Mixing Units

DOI: 10.12677/MOS.2024.131007, PP. 61-74

Keywords: 微混合器,分离和重组单元,优化,混合效率
Micromixer
, Split and Recombination Unit, Optimization, Mixing Efficiency

Full-Text   Cite this paper   Add to My Lib

Abstract:

分离重组(SAR)技术是增强微混合器混合效率的有效方法之一,该技术是利用混合单元将流体不断地分离再重组来达到混合目的。目前,大量的混合单元被提出。然而,这些单元的组合对混合的影响尚未被研究。因此,本文基于多样性混合单元,提出一种具有高混合效率的分离重组微混合器。采用菱形、圆形、方形三种差异性结构,这些结构两两组合出九种混合单元,再将这些混合单元分别放入带有三个混合区域的微混合器模型,并通过数值仿真和试验方法分析不同组合下的混合效率。仿真结果表明,菱形结构对微混合器的混合性能提升最大,圆形最弱,带有菱形和方形结构的分离重组微混合器(YOSAR)组合最优。随着雷诺数的增加,YOSAR内流体的混沌平流和迪安流效应加剧,混合效率增加。在雷诺数为100时,YOSAR混合效率达到99%,接近于完全混合。同时,实验结果和仿真结果具有一致性。
The split and recombination (SAR) technique is one of the effective methods to enhance the mixing efficiency of a micromixer. It utilizes mixing units to continuously separate and then reorganize flu-ids for mixing purposes. Although numerous mixing units have been proposed at present, the com-bined effect of these units on mixing has not been investigated. Hence, this article proposes a sepa-ration and recombination micromixer with high mixing efficiency based on diverse mixing units. Three differentiated structures, square, circle, and rhombus, are utilized and combined in pairs, resulting in nine different mixing units. These units are then integrated into a micromixer model with three mixing regions. The mixing efficiency of different combinations is analyzed using numer-ical simulation and experimental methods. The simulation results reveal that the rhombic struc-ture enhances the mixing performance of the micromixer the most, while the circular structure is the weakest. The combination of the rhombic and square structures (YOSAR) demonstrates the op-timum performance. As the Reynolds number increases, the chaotic advection and Dean flow effects intensify within the YOSAR, leading to improved mixing efficiency. At a Reynolds number of 100, the YOSAR mixing efficiency reaches 99%, approaching complete mixing. Meanwhile, the experi-mental and simulation results are consistent.

References

[1]  Chin, C.D., Linder, V. and Sia, S.K. (2007) Lab-on-a-Chip Devices for Global Health: Past Studies and future Opportu-nities. Lab on a Chip, 7, 41-57.
https://doi.org/10.1039/B611455E
[2]  Ma, J., Wu, Y., Liu, Y., et al. (2021) Cell-Sorting Centrifugal Microfluidic Chip with a Flow Rectifier. Lab on a Chip, 21, 2129-2141.
https://doi.org/10.1039/D1LC00217A
[3]  Liu, T., Yin, Y., Yang, Y., et al. (2022) Layer-by-Layer Engineered All-Liquid Microfluidic Chips for Enzyme Immobilization. Advanced Materials, 34, Article ID: 2105386.
https://doi.org/10.1002/adma.202105386
[4]  Sun, J., Ren, Y., Ji, J., et al. (2021) A Novel Concentration Gradient Microfluidic Chip for High-Throughput Antibiotic Susceptibility Testing of Bacteria. Analytical and Bioanalytical Chem-istry, 413, 1127-1136.
https://doi.org/10.1007/s00216-020-03076-8
[5]  Yang, B., Wang, P., Li, Z., et al. (2022) A Continuous Flow PCR Array Microfluidic Chip Applied for Simultaneous Amplification of Target Genes of Periodontal Pathogens. Lab on a Chip, 22, 733-737.
https://doi.org/10.1039/D1LC00814E
[6]  Fu, G., Zhou, W. and Li, X.J. (2020) Remotely Tunable Microfluidic Platform Driven by Nanomaterial-Mediated On-Demand Photothermal Pumping. Lab on a Chip, 20, 2218-2227.
https://doi.org/10.1039/D0LC00317D
[7]  Wei, Z., Fan, P., Jiao, Y., et al. (2020) Integrated Microfluidic Chip for On-Line Proteome Analysis with Combination of Denaturing and Rapid Digestion of Protein. Analytica Chimica Acta, 1102, 1-10.
https://doi.org/10.1016/j.aca.2020.01.025
[8]  Li, Z., Zhang, B., Dang, D., et al. (2022) A Review of Microfluid-ic-Based Mixing Methods. Sensors and Actuators A: Physical, 2022, Article ID: 113757.
https://doi.org/10.1016/j.sna.2022.113757
[9]  Angelopoulou, M., Petrou, P.S., Makarona, E., et al. (2018) Ultra-fast Multiplexed-Allergen Detection through Advanced Fluidic Design and Monolithic Interferometric Silicon Chips. An-alytical Chemistry, 90, 9559-9567.
https://doi.org/10.1021/acs.analchem.8b02321
[10]  Bayareh, M., Ashani, M.N. and Usefian, A. (2020) Active and Passive Micromixers: A Comprehensive Review. Chemical Engineering and Processing-Process Intensification, 147, Article ID: 107771.
https://doi.org/10.1016/j.cep.2019.107771
[11]  Liu, G., Wang, M., Li, P., et al. (2022) A Micromixer Driven by Two Valveless Piezoelectric Pumps with Multi-Stage Mixing Characteristics. Sensors and Actuators A: Physical, 333, Article ID: 113225.
https://doi.org/10.1016/j.sna.2021.113225
[12]  Nazari, M., Rashidi, S. and Esfahani, J.A. (2019) Mixing Process and Mass Transfer in a Novel Design of Induced-Charge Electrokinetic Micromixer with a Conductive Mixing-Chamber. International Communications in Heat and Mass Transfer, 108, Article ID: 104293.
https://doi.org/10.1016/j.icheatmasstransfer.2019.104293
[13]  Kumar, C., Hejazian, M., From, C., et al. (2019) Modeling of Mass Transfer Enhancement in a Magnetofluidic Micromixer. Physics of Fluids, 31, Article ID: 063603.
https://doi.org/10.1063/1.5093498
[14]  Huang, P.H., Xie, Y., Ahmed, D., et al. (2013) An Acoustofluidic Micro-mixer Based on Oscillating Sidewall Sharp-Edges. Lab on a Chip, 13, 3847-3852.
https://doi.org/10.1039/c3lc50568e
[15]  Park, S., Chuang, H.S. and Kwon, J.S. (2021) Numerical Study and Taguchi Optimization of Fluid Mixing by a Microheater-Modulated Alternating Current Electrothermal Flow in a Y-Shape Microchannel. Sensors and Actuators B: Chemical, 329, Article ID: 129242.
https://doi.org/10.1016/j.snb.2020.129242
[16]  Chen, X. and Li, T. (2017) A Novel Passive Micromixer Designed by Applying an Optimization Algorithm to the Zigzag Microchannel. Chemical Engineering Journal, 313, 1406-1414.
https://doi.org/10.1016/j.cej.2016.11.052
[17]  Liu, C., Li, Y. and Liu, B.F. (2019) Micromixers and Their Applica-tions in Kinetic Analysis of Biochemical Reactions. Talanta, 205, Article ID: 120136.
https://doi.org/10.1016/j.talanta.2019.120136
[18]  Chen, X. and Zhao, Z. (2017) Numerical Investigation on Layout Optimization of Obstacles in a Three-Dimensional Passive Micromixer. Analytica Chimica Acta, 964, 142-149.
https://doi.org/10.1016/j.aca.2017.01.066
[19]  Dadvand, A., Hosseini, S., Aghebatandish, S., et al. (2019) En-hancement of Heat and Mass Transfer in a Microchannel via Passive Oscillation of a Flexible Vortex Generator. Chemi-cal Engineering Science, 207, 556-580.
https://doi.org/10.1016/j.ces.2019.06.045
[20]  Hossain, S., Husain, A. and Kim, K.Y. (2010) Shape Optimization of a Micromixer with Staggered-Herringbone Grooves Patterned on Opposite Walls. Chemical Engineering Journal, 162, 730-737.
https://doi.org/10.1016/j.cej.2010.05.056
[21]  Wangikar, S.S., Patowari, P.K. and Misra, R.D. (2018) Numerical and Experimental Investigations on the Performance of a Serpentine Microchannel with Semicircular Obstacles. Mi-crosystem Technologies, 24, 3307-3320.
https://doi.org/10.1007/s00542-018-3799-0
[22]  Kim, K., Shah, I., Ali, M., et al. (2020) Experimental and Numer-ical Analysis of Three Y-Shaped Split and Recombination Micromixers Based on Cantor Fractal Structures. Microsystem Technologies, 26, 1783-1796.
https://doi.org/10.1007/s00542-019-04724-5
[23]  Gidde, R.R., Wangikar, S.S., Pawar, P.M., et al. (2022) A Comparative Study: Conventional and Modified Serpentine Micromixers. Chemical Product and Process Modeling, 18, 521-539.
https://doi.org/10.1515/cppm-2022-0022
[24]  Ansari, M.A. and Kim, K.Y. (2010) Mixing Performance of Unbalanced Split and Recombine Micomixers with Circular and Rhombic Sub-Channels. Chemical Engineering Journal, 162, 760-767.
https://doi.org/10.1016/j.cej.2010.05.068
[25]  Chen, X. and Shen, J. (2017) Simulation and Experimental Analysis of a SAR Micromixer with F-Shape Mixing Units. Analytical Methods, 9, 1885-1890.
https://doi.org/10.1039/C7AY00022G
[26]  Shah, I., Kim, S.W., Kim, K., et al. (2019) Experimental and Numerical Analysis of Y-Shaped Split and Recombination Micro-Mixer with Different Mixing Units. Chemical Engineering Jour-nal, 358, 691-706.
https://doi.org/10.1016/j.cej.2018.09.045
[27]  Viktorov, V. and Nimafar, M. (2013) A Novel Generation of 3D SAR-Based Passive Micromixer: Efficient Mixing and Low Pressure Drop at a Low Reynolds Number. Journal of Mi-cromechanics and Microengineering, 23, Article ID: 055023.
https://doi.org/10.1088/0960-1317/23/5/055023
[28]  Afzal, A. and Kim, K.Y. (2012) Passive Split and Recombi-nation Micromixer with Convergent-Divergent Walls. Chemical Engineering Journal, 203, 182-192.
https://doi.org/10.1016/j.cej.2012.06.111
[29]  Mollajan, M., Razavi Bazaz, S. and AboueiMehrizi, A. (2018) A Thoroughgoing Design of a Rapid-Cycle Microfluidic Droplet-Based PCR Device to Amplify Rare DNA Strands. Journal of Applied Fluid Mechanics, 11, 21-29.
https://doi.org/10.29252/jafm.11.01.28110
[30]  Chen, X. and Shen, J. (2017) Numerical and Experimental Investi-gation on Splitting-and-Recombination Micromixer with E-Shape Mixing Units. Microsystem Technologies, 23, 4671-4677.
https://doi.org/10.1007/s00542-016-3208-5
[31]  Lee, C.Y., Wang, W.T., Liu, C.C., et al. (2016) Pas-sive Mixers in Microfluidic Systems: A Review. Chemical Engineering Journal, 288, 146-160.
https://doi.org/10.1016/j.cej.2015.10.122
[32]  Hsiao, K.Y., Wu, C.Y. and Huang, Y.T. (2014) Fluid Mixing in a Microchannel with Longitudinal Vortex Generators. Chemical Engineering Journal, 235, 27-36.
https://doi.org/10.1016/j.cej.2013.09.010
[33]  Xiong, S. and Chen, X. (2021) Simulation and Experimental Re-search of an Effective SAR Multilayer Interlaced Micromixer Based on Koch Fractal Geometry. Microfluidics and Nanofluidics, 25, Article No. 92.
https://doi.org/10.1007/s10404-021-02495-y
[34]  Liu, G., Wang, M., Dong, L., et al. (2022) A Novel Design for Split-and-Recombine Micromixer with Double-Layer Y-Shaped Mixing Units. Sensors and Actuators A: Physical, 341, Article ID: 113569.
https://doi.org/10.1016/j.sna.2022.113569
[35]  Li, J., Xia, G. and Li, Y. (2013) Numerical and Experimental Anal-yses of Planar Asymmetric Split-and-Recombine Micromixer with Dislocation Sub-Channels. Journal of Chemical Technology & Biotechnology, 88, 1757-1765.
https://doi.org/10.1002/jctb.4044
[36]  Husain, A., Khan, F.A., Huda, N., et al. (2018) Mixing Performance of Split-and-Recombine Micromixer with Offset Inlets. Microsystem Technologies, 24, 1511-1523.
https://doi.org/10.1007/s00542-017-3516-4
[37]  Lashkaripour, A., Rodriguez, C., Ortiz, L., et al. (2019) Perfor-mance Tuning of Microfluidic Flow-Focusing Droplet Generators. Lab on a Chip, 19, 1041-1053.
https://doi.org/10.1039/C8LC01253A
[38]  Ansari, M.A., Kim, K.Y., Anwar, K., et al. (2010) A Novel Passive Micromixer Based on Unbalanced Splits and Collisions of Fluid Streams. Journal of Micromechanics and Microengi-neering, 20, Article ID: 055007.
https://doi.org/10.1088/0960-1317/20/5/055007

Full-Text

comments powered by Disqus

Contact Us

service@oalib.com

QQ:3279437679

WhatsApp +8615387084133

WeChat 1538708413