This study explored the performances of CZTS-based thin-film solar cell with three novel buffer layer materials ZnS, CdS, and CdZnS, as well as with variation in thickness of buffer and absorber-layer, doping concentrations of absorber-layer material and operating temperature. Our aims focused to identify the most optimal thin-film solar cell structure that offers high efficiency and lower toxicity which are desirable for sustainable and eco-friendly energy sources globally. SCAPS-1D, widely used software for modeling and simulating solar cells, has been used and solar cell fundamental performance parameters such as open-circuited voltage (), short-circuited current density (), fill-factor() and efficiency() have been optimized in this study. Based on our simulation results, it was found that CZTS solar cell with Cd0.4Zn0.6S as buffer-layer offers the most optimal combination of high efficiency and lower toxicity in comparison to other structure investigated in our study. Although the efficiency of Cd0.4Zn0.6S, ZnS and CdS are comparable, Cd0.4Zn0.6S is preferable to use as buffer-layer for its non-toxic property. In addition, evaluation of performance as a function of buffer-layer thickness for Cd0.4Zn0.6S, ZnS and CdS showed that optimum buffer-layer thickness for Cd0.4Zn0.6S was in the range from 50 to 150nm while ZnS offered only 50 – 75 nm. Furthermore, the temperature dependence performance parameters evaluation revealed that it is better to operate solar cell at temperature 290K for stable operation with optimum performances. This study would provide valuable insights into design and optimization of nanotechnology-based solar energy technology for minimizing global energy crisis and developing eco-friendly energy sources sustainable and simultaneously.
References
[1]
Owusu, P.A. and Asumadu-Sarkodie, S. (2016) A Review of Renewable Energy Sources, Sustainability Issues and Climate Change Mitigation. Cogent Engineering, 3, Article ID: 1167990. https://doi.org/10.1080/23311916.2016.1167990
[2]
Shiyani, T., Mahapatra, S.K. and Banerjee, I. (2023) Plasmonic Solar Cells. In: Inamuddin, Ahamed, M.I., Boddula, R. and Rezakazemi, M., Eds., Fundamentals of Solar Cell Design, John Wiley & Sons, Hoboken, 55-81. https://doi.org/10.1002/9781119725022.ch2
[3]
Bilgen, S. (2014) Structure and Environmental Impact of Global Energy Consumption. Renewable and Sustainable Energy Reviews, 38, 890-902. https://doi.org/10.1016/j.rser.2014.07.004
[4]
Islam, M.M. and Hasanuzzaman, M. (2020) Introduction to Energy and Sustainable Development. In: Hasanuzzaman, M.D. and Rahim, N.A., Eds., Energy for Sustainable Development: Demand, Supply, Conversion and Management, Elsevier, Amsterdam, 1-18. https://doi.org/10.1016/B978-0-12-814645-3.00001-8
[5]
Maka, A.O.M. and Alabid, J.M. (2022) Solar Energy Technology and Its Roles in Sustainable Development. Clean Energy, 6, 476-483. https://doi.org/10.1093/ce/zkac023
[6]
Kabir, E., Kumar, P., Kumar, S., Adelodun, A.A. and Kim, K.H. (2018) Solar Energy: Potential and Future Prospects. Renewable and Sustainable Energy Reviews, 82, 894-900. https://doi.org/10.1016/j.rser.2017.09.094
[7]
NREL (2021) Documenting a Decade of Cost Declines for PV Systems Documenting a Decade of Cost Declines for PV Systems. The National Renewable Energy Laboratory (NREL), Golden, 23-25. https://www.nrel.gov/news/program/2021/documenting-a-decade-of-cost-declines-for-pv-systems.html
[8]
Yasodharan, R., Senthilkumar, A.P., Mohankumar, P. and Ajayan, J. (2020) Investigation and Influence of Layer Composition of Tandem Perovskite Solar Cells for Applications in Future Renewable and Sustainable Energy. Optik (Stuttg), 212, Article ID: 164723. https://doi.org/10.1016/j.ijleo.2020.164723
[9]
Mazzucato, S., et al. (2012) Dilute Nitride and GaAs N-I-P-I Solar Cells. Nanoscale Research Letters, 7, Article No. 631. https://doi.org/10.1186/1556-276X-7-631
[10]
Deshpande, R.A. (2021) Advances in Solar Cell Technology: An Overview. Journal of Scientific Research, 65, 72-75. https://doi.org/10.37398/JSR.2021.650214
[11]
Moon, S., Kim, K., Kim, Y., Heo, J. and Lee, J. (2016) Highly Efficient Single-Junc-tion GaAs Thin-Film Solar Cell on Flexible Substrate. Scientific Reports, 6, Article No. 30107. https://doi.org/10.1038/srep30107
[12]
Elshorbagy, M.H., Abdel-Hady, K., Kamal, H. and Alda, J. (2017) Broadband Anti-Reflection Coating Using Dielectric Si3N4 Nanostructures. Application to Amor-phous-Si-H Solar Cells. Optics Communications, 390, 130-136. https://doi.org/10.1016/j.optcom.2016.12.062
[13]
Ingrid Repins, Y., et al. (2008) 19.9%-Efficient ZnO/CdS/CuInGaSe2 Solar Cell with 81.2% Fill Factor. Progress in Photovoltaics: Research and Applications, 16, 235-239. https://doi.org/10.1002/pip.822
[14]
Jackson, P., et al. (2011) New World Record Efficiency for Cu(In,Ga)Se2 Thin-Film Solar Cells beyond 20%. Progress in Photovoltaics: Research and Applications, 19, 894-897. https://doi.org/10.1002/pip.1078
[15]
Swati, S., Matin, R., Bashar, S. and Mahmood, Z. (2018) Experimental Study of the Optical Properties of Cu2ZnSnS4 Thin Film Absorber Layer for Solar Cell Application. Journal of Physics: Conference Series, 1086, Article ID: 012010. https://doi.org/10.1088/1742-6596/1086/1/012010
[16]
Wang, H. and Gong, Y. (2011) Low Temperature Synthesized Quaternary Chalcogenide Cu2ZnSnS4 from Nano-Crystallite Binary Sulfides. Journal of the Electrochemical Society, 15, H800-H803. https://doi.org/10.1149/1.3598168
[17]
Ahmoum, M., Chelvanathan, H. and Su’Ait, P. (2021) Sol-Gel Prepared Cu2ZnSnS4 (CZTS) Semiconductor Thin Films: Role of Solvent Removal Processing Temperature. Materials Science in Semiconductor Processing, 132, Article ID: 105874. https://doi.org/10.1016/j.mssp.2021.105874
[18]
Mkawi, E.M., Al-Hadeethi, Y., Shalaan, E. and Bekyarova, E. (2020) Solution-Processed Sphere-Like Cu2ZnSnS4 Nanoparticles for Solar Cells: Effect of Oleylamine Concentration on Properties. Applied Physics A: Materials Science and Processing, 126, Article No. 50. https://doi.org/10.1007/s00339-019-3233-1
[19]
Yu, S.M., Lim, K.S., Shin, D.W., Oh, T.S. and Yoo, J.B. (2017) Effect of the Intermediate Sulfide Layer on the Cu2ZnSnS4-Based Solar Cells. Journal of Materials Science: Materials in Electronics, 28, 5696-5702. https://doi.org/10.1007/s10854-016-6241-3
[20]
Eisele, W., et al. (2003) XPS, TEM and NRA Investigations of Zn(Se,OH)/Zn(OH)2 Films on Cu(In,Ga)(S,Se)2 Substrates for Highly Efficient Solar Cells. Solar Energy Materials and Solar Cells, 75, 17-26. https://doi.org/10.1016/S0927-0248(02)00104-6
[21]
Yasin, S., Waar, Z.A. and Al Zoubi, T. (2020) Development of High Efficiency CZTS Solar Cell through Buffer Layer Parameters Optimization Using SCAPS-1D. Materials Today: Proceedings, 33, 1825-1829. https://doi.org/10.1016/j.matpr.2020.05.064
[22]
Akcay, S., Zaretskaya, N. and Ozcelik, E. (2019) Development of a CZTS Solar Cell with CdS Buffer Layer Deposited by RF Magnetron Sputtering. Journal of Alloys and Compounds, 772, 782-792. https://doi.org/10.1016/j.jallcom.2018.09.126
[23]
Nguyen, M., et al. (2015) ZnS Buffer Layer for Cu2ZnSn(SSe)4 Monograin Layer Solar Cell. Solar Energy, 111, 344-349. https://doi.org/10.1016/j.solener.2014.11.006
[24]
Mazumder, S. and Senthilkumar, K. (2022) Device Study and Optimisation of CZTS/ZnS Based Solar Cell with CuI Hole Transport Layer for Different Conduction Band Offset. Solar Energy, 237, 414-431. https://doi.org/10.1016/j.solener.2022.03.036
[25]
Zhou, Z., Zhao, K. and Huang, F. (2010) Optical Properties of Cd1−xZnxS Thin Films for CuInGaSe2 Solar Cell Application. Materials Research Bulletin, 45, 1537-1540. https://doi.org/10.1016/j.materresbull.2010.06.005
[26]
Zhang, X., et al. (2022) Synthesis of CdZnS Buffer Layer and Its Impact on Cu2ZnSn(S,Se)4 Thin Film Solar Cells. Journal of Materials Science: Materials in Electronics, 33, 2399-2405. https://doi.org/10.1007/s10854-021-07446-5
[27]
Zein, W., Alanazi, T.I., Salah, M.M. and Saeed, A. (2023) Concurrent Design of Alloy Compositions of CZTSSe and CdZnS Using SCAPS Simulation: Potential Routes to Overcoming VOC Deficit. Energies, 16, Article No. 5754. https://doi.org/10.3390/en16155754
[28]
Jhuma, F.A., Shaily, M.Z. and Rashid, M.J. (2019) Towards High-Efficiency CZTS Solar Cell through Buffer Layer Optimization. Materials for Renewable and Sustainable Energy, 8, Article No. 6. https://doi.org/10.1007/s40243-019-0144-1
[29]
Verschraegen, M. and Burgelman, J. (2007) Numerical Modeling of Intra-Band Tunneling for Heterojunction Solar Cells in Scaps. Thin Solid Films, 515, Article No. 6276. https://doi.org/10.1016/j.tsf.2006.12.049
[30]
Hima, N. and Lakhdar, A. (2020) Enhancement of Efficiency and Stability of CH3NH3GeI3 Solar Cells with CuSbS2. Optical Materials (Amst), 99, Article ID: 109607. https://doi.org/10.1016/j.optmat.2019.109607
[31]
Pindolia, G., Shinde, S.M. and Jha, P.K. (2022) Optimization of an Inorganic Lead Free RbGeI3 Based Perovskite Solar Cell by SCAPS-1D Simulation Optimization of an Inorganic Lead Free RbGeI3 Based Perovskite Solar Cell by SCAPS-1D Simulation. Solar Energy, 236, 802-821. https://doi.org/10.1016/j.solener.2022.03.053
[32]
Yasin, S., Waar, Z.A. and Al Zoubi, T. (2020) Development of High Efficiency CZTS Solar Cell through Buffer Layer Parameters Optimization Using SCAPS-1D. Materials Today: Proceedings, 33, 1825-1829. https://doi.org/10.1016/j.matpr.2020.05.064
[33]
Ouslimane, T., Et-Taya, L., Elmaimouni, L. and Benami, A. (2021) Impact of Absorber Layer Thickness, Defect Density, and Operating Temperature on the Performance of MAPbI3 Solar Cells Based on ZnO Electron Transporting Material. Heliyon, 7, E06379. https://doi.org/10.1016/j.heliyon.2021.e06379
[34]
Mbopda Tcheum, J.M.B., Teyou Ngoupo, G.L., Ouédraogo, A., Guirdjebaye, S. and Ndjaka, N. (2020) Numerical Analysis of Ultrathin Cu(In,Ga )Se2 Solar Cells with Zn(O,S) Buffer Layer. Pramana, 94, Article No. 111. https://doi.org/10.1007/s12043-020-01977-y
[35]
Baloch, A.A.B., Aly, S.P., Hossain, M.I. and El-Mellouhi, F. (2017) Full Space Device Optimization for Solar Cells. Scientific Reports, 7, Article No. 11984. https://doi.org/10.1038/s41598-017-12158-0
[36]
Chang, K., Tian, W.H., Fang, H.M., Guo, G.C., Wang, D. and Zhao, Z. (2019) Simulation of Innovative High Efficiency Perovskite Solar Cell with Bi-HTL: NiO and Si Thin Films. Solar Energy, 186, 323-327. https://doi.org/10.1016/j.solener.2019.05.017
[37]
Garmim, T., et al. (2022) Effect of Alternative Buffer Layers for SnS Based Solar Cells: Numerical Analysis Using SCAPS-1D. Materials Today: Proceedings, 66, 146-150. https://doi.org/10.1016/j.matpr.2022.04.289
[38]
Wang, Y., et al. (2015) Towards Printed Perovskite Solar Cells with Cuprous Oxide Hole Trans-Porting Layers: A Theoretical Design. Semiconductor Science and Technology, 30, Article ID: 054004. https://doi.org/10.1088/0268-1242/30/5/054004
[39]
Belarbi, F., Rahal, W., Rached, D., Benghabrit, S. and Adnane, M. (2020) A Comparative Study of Different Buffer Layers for CZTS Solar Cell Using Scaps-1D Simulation Program. Optik (Stuttg), 216, Article ID: 164743. https://doi.org/10.1016/j.ijleo.2020.164743
[40]
Zhou, X. and Han, J. (2020) Design and Simulation of C2N Based Solar Cell by SCAPS-1D Software. Materials Research Express, 7, Article ID: 126303. https://doi.org/10.1088/2053-1591/abcdd6
[41]
Moustafa, M., Al Zoubi, T. and Yasin, S. (2022) Exploration of CZTS-Based Solar Using the ZrS2 as a Novel Buffer Layer by SCAPS Simulation. Optical Materials (Amst), 124, Article ID: 112001. https://doi.org/10.1016/j.optmat.2022.112001
[42]
Daoudia, A.K., El Hassouani, Y. and Benami, A. (2016) Investigation of the Effect of Thickness, Band Gap and Temperature on the Efficiency of CIGS Solar Cells through SCAPS-1D. International Journal of Engineering and Technology Research, 6, 71-75.
[43]
Varshni, Y.P. (1967) Temperature Dependence of the Energy Gap in Semiconductors. Physica, 34, 149-154. https://doi.org/10.1016/0031-8914(67)90062-6
[44]
Alam, I. and Ashraf, A. (2020) Effect of Different Device Parameters on Tin Based Perovskite Solar Cell Coupled with In2S3 Electron Transport Layer and CuSCN and Spiro-OMeTAD Alternative Hole Transport Layers for High Efficiency Performance. Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, 159, 1-17. https://doi.org/10.1080/15567036.2020.1820628
[45]
Priyanka Singh, N.M.R. (2012) Temperature. Solar Energy Materials and Solar Cells, 101, 36-45. https://doi.org/10.1016/j.solmat.2012.02.019
[46]
Abdelfatah, M., et al. (2016) Solar Energy Materials and Solar Cells Fabrication and Characterization of Low Cost Cu2O/ZnO: Al Solar Cells for Sustainable Photovoltaics with Earth Abundant Materials. Solar Energy Materials and Solar Cells, 145, 454-461. https://doi.org/10.1016/j.solmat.2015.11.015
[47]
Moon, M.M.A., Ali, M.H., Rahman, M.F. and Hossain, J. (2020) Design and Simulation of FeSi-Based Novel Heterojunction Solar Cells for Harnessing Visible and Near-Infrared Light. Physica Status Solidi, 217, Article ID: 1900921. https://doi.org/10.1002/pssa.201900921
![](\"https://html.scirp.org//file/6202888-rId13.svg?20240417020405\")
), short-circuited current density (![](\"https://html.scirp.org//file/6202888-rId15.svg?20240417020405\")
), fill-factor(![](\"https://html.scirp.org//file/6202888-rId17.svg?20240417020405\")
) and efficiency(![](\"https://html.scirp.org//file/6202888-rId19.svg?20240417020405\")
) have been optimized in this study. Based on our simulation results, it was found that CZTS solar cell with Cd0.4Zn0.6S as buffer-layer offers the most optimal combination of high efficiency and lower toxicity in comparison to other structure investigated in our study. Although the efficiency of Cd0.4Zn0.6S, ZnS and CdS are comparable, Cd0.4Zn0.6S is preferable to use as buffer-layer for its non-toxic property. In addition, evaluation of performance as a function of buffer-layer thickness for Cd0.4Zn0.6S, ZnS and CdS showed that optimum buffer-layer thickness for Cd0.4Zn0.6S was in the range from 50 to 150nm while ZnS offered only 50 – 75 nm. Furthermore, the temperature dependence performance parameters evaluation revealed that it is better to operate solar cell at temperature 290K for stable operation with optimum performances. This study would provide valuable insights into design and optimization of nanotechnology-based solar energy technology for minimizing global energy crisis and developing eco-friendly energy sources sustainable and simultaneously.
