In South Saharan countries, 85% of the population uses biomass as a primary energy source. Cameroon presents one of the highest biomass energy and sawmills produce important sawdust resources which are not used and are burnt in piles leading to significant air toxic emissions. Therefore, we have to valorize industrially these available sawdusts. This study focuses on the physicochemical and thermochemical analysis of Ayous, Sapelli and Tali sawdust. The proximate and ultimate analysis, particle size, structural composition, as well as heavy metal content and calorific value were determined. In addition, the thermogravimetric mass losses were also estimated. The results showed that high water contents (24% - 41%) were recorded in the raw sawdust, and the thermal treatment reduced these contents from 78% to values in the range of 4% - 9%. The values for ash and volatile matter content were respectively between 0.25% - 0.74% and 68% - 76%. The LHV is higher in Ayous (17.5 MJ/kg) and Sapelli (16.8 MJ/kg) than that of Tali (15.7 MJ/kg). The concentration of heavy metals is very low in each species. Extractives are more present in Tali (16.06%) than in the other sawdusts. Pyrolysis of sawdust shows the typical decomposition of hemicellulose (270˚C - 325˚C), cellulose (325˚C - 400˚C) and lignin (200˚C - 550˚C) with a maximum loss of 75% at 370˚C and the melting point is 320˚C. The results of the sawdust parameters determined in the paper can be valorized to reduce pollutants emissions by developing the efficiency and effectiveness of biomass energy processes and promoting the use of biomass as a sustainable alternative to traditional fossil fuels.
References
[1]
Perera, F. (2018) Pollution from Fossil-Fuel Combustion Is the Leading Environmental Threat to Global Pediatric Health and Equity: Solutions Exist. International Journal of Environmental Research and Public Health, 15, Article 16. https://doi.org/10.3390/ijerph15010016
[2]
Schmidt, T.S., Matsuo, T. and Michaelowa, A. (2017) Renewable Energy Policy as an Enabler of Fossil Fuel Subsidy Reform? Applying a Socio-Technical Perspective to the Cases of South Africa and Tunisia. Global Environmental Change, 45, 99-110. https://doi.org/10.1016/j.gloenvcha.2017.05.004
[3]
Kulas, D., Winjobi, O., Zhou, W. and Shonnard, D. (2018) Effects of Coproduct Uses on Environmental and Economic Sustainability of Hydrocarbon Biofuel from One-and Two-Step Pyrolysis of Poplar. ACS Sustainable Chemistry & Engineering, 6, 5969-5980. https://doi.org/10.1021/acssuschemeng.7b04390
[4]
Coady, D., Parry, I., Sears, L. and Shang, B. (2017) How Large Are Global Fossil Fuel Subsidies? World Development, 91, 11-27. https://doi.org/10.1016/j.worlddev.2016.10.004
[5]
Carpenter, D., Westover, T.L., Czernik, S. and Jablonski, W. (2014) Biomass Feedstocks for Renewable Fuel Production: A Review of the Impacts of Feedstock and Pretreatment on the Yield and Product Distribution of Fast Pyrolysis Bio-Oils and Vapors. Green Chemistry, 16, 384-406. https://doi.org/10.1039/C3GC41631C
[6]
Lee, M., Lin, Y.-L., Chiueh, P.-T. and Den, W. (2020) Environmental and Energy Assessment of Biomass Residues to Biochar as Fuel: A Brief Review with Recommendations for Future Bioenergy Systems. Journal of Cleaner Production, 251, Article 119714. https://doi.org/10.1016/j.jclepro.2019.119714
[7]
Chen, W.-H., Cheng, W.-Y., Lu, K.-M. and Huang, Y.-P. (2011) An Evaluation on Improvement of Pulverized Biomass Property for Solid Fuel through Torrefaction. Applied Energy, 88, 3636-3644. https://doi.org/10.1016/j.apenergy.2011.03.040
[8]
Dasappa, S. (2011) Potential of Biomass Energy for Electricity Generation in Sub-Saharan Africa. Energy for Sustainable Development, 15, 203-213. https://doi.org/10.1016/j.esd.2011.07.006
[9]
Alazraque-Cherni, J. (2008) Renewable Energy for Rural Sustainability in Developing Countries. Bulletin of Science, Technology & Society, 28, 105-114. https://doi.org/10.1177/0270467607313956
[10]
Reddy, K.V., Sree, N.R.S., Ranjit, P. and Maddela, N.R. (2023) Biomass Waste and Feedstock as a Source of Renewable Energy. In: Shah, M.P., Ed., Green Approach to Alternative Fuel for a Sustainable Future, Elsevier, Amsterdam, 325-334. https://doi.org/10.1016/B978-0-12-824318-3.00033-3
[11]
Simo, A. and Siyam Siwe, S. (2000) Availability and Conversion to Energy Potentials of Wood-Based Industry Residues in Cameroon. Renewable Energy, 19, 213-218. https://doi.org/10.1016/S0960-1481(99)00033-6
[12]
Mboumboue, E. and Njomo, D. (2016) Potential Contribution of Renewables to the Improvement of Living Conditions of Poor Rural Households in Developing Countries: Cameroon’s Case Study. Renewable and Sustainable Energy Reviews, 61, 266-279. https://doi.org/10.1016/j.rser.2016.04.003
[13]
Lescuyer, G. and Tal, M. (2016) Exportations de bois du Cameroun vers le Tchad: Un succès commercial mais une légalité défaillante. Bois et Forets des Tropiques, 329, 67-77. https://doi.org/10.19182/bft2016.329.a31313
[14]
Lescuyer, G., Atyi, R.E. and Cerutti, P.O. (2009) Consommations nationales de bois d’øeuvre en Afrique centrale: Un enjeu majeur pour la gestion forestière durable. XIII Congrès Forestier Mondial, Buenos Aires, 18-23 October 2009, 1-14.
[15]
Kenfack, J., Bossou, O.V. and Tchaptchet, E. (2017) How Can We Promote Renewable Energy and Energy Efficiency in Central Africa? A Cameroon Case Study. Renewable and Sustainable Energy Reviews, 75, 1217-1224. https://doi.org/10.1016/j.rser.2016.11.108
[16]
Ackom, E.K., Alemagi, D., Ackom, N.B., Minang, P.A. and Tchoundjeu, Z. (2013) Modern Bioenergy from Agricultural and Forestry Residues in Cameroon: Potential, Challenges and the Way Forward. Energy Policy, 63, 101-113. https://doi.org/10.1016/j.enpol.2013.09.006
[17]
Nzotcha U. and Kenfack, J. (2019) Contribution of the Wood-Processing Industry for Sustainable Power Generation: Viability of Biomass-Fuelled Cogeneration in Sub-Saharan Africa. Biomass and Bioenergy, 120, 324-331. https://doi.org/10.1016/j.biombioe.2018.11.015
[18]
Demirbas, A. (2004) Current Technologies for the Thermo-Conversion of Biomass into Fuels and Chemicals. Energy Sources, 26, 715-730. https://doi.org/10.1080/00908310490445562
[19]
Wicke, B., Smeets, E., Watson, H. and Faaij, A. (2011) The Current Bioenergy Production Potential of Semi-Arid and Arid Regions in Sub-Saharan Africa. Biomass and Bioenergy, 35, 2773-2786. https://doi.org/10.1016/j.biombioe.2011.03.010
[20]
Bot, B.V., Tamba, J.G. and Sosso, O.T. (2022) Assessment of Biomass Briquette Energy Potential from Agricultural Residues in Cameroon. Biomass Conversion and Biorefinery, 14, 1905-1917. https://doi.org/10.1007/s13399-022-02388-2
[21]
Tom, A., Tame, A., Djonga, P.N.D., Justin, B.T.D. and Abena, E.G.N. (2021) Thermal and Physicochemical Characterization of Fibers from Coffee Hulls as Filler for Linear Low-Density Polyethylene. Advances in Materials Physics and Chemistry, 11, 155-166. https://doi.org/10.4236/ampc.2021.1110015
[22]
Stelte, W., Sanadi, A.R., Shang, L., Holm, J.K., Ahrenfeldt, J. and Henriksen, U.B. (2012) Recent Developments in Biomass Pelletization—A Review. BioResources, 7, 4451-4490. https://doi.org/10.15376/biores.7.3.Stelte
[23]
Gaqa, S., Mamphweli, S., Katwire, D. and Meyer, E. (2014) The Properties and Suitability of Various Biomass/Coal Blends for Co-Gasification Purposes. Journal of Sustainable Bioenergy Systems, 4, 175-182. https://doi.org/10.4236/jsbs.2014.43016
[24]
Iftikhar, M., Asghar, A., Ramzan, N., Sajjadi, B. and Chen, W. (2019) Biomass Densification: Effect of Cow Dung on the Physicochemical Properties of Wheat Straw and Rice Husk-Based Biomass Pellets. Biomass and Bioenergy, 122, 1-16. https://doi.org/10.1016/j.biombioe.2019.01.005
[25]
Whittaker, C. and Shield, I. (2017) Factors Affecting Wood, Energy Grass and Straw Pellet Durability—A Review. Renewable and Sustainable Energy Reviews, 71, 1-11. https://doi.org/10.1016/j.rser.2016.12.119
[26]
Tchinda, J.-B.S., et al. (2018) Inhibition of Fungi with Wood Extractives and Natural Durability of Five Cameroonian Wood Species. Industrial Crops and Products, 123, 183‑191. https://doi.org/10.1016/j.indcrop.2018.06.078
[27]
Tarpilga. M.D.C., Naon. B. and Ouedraogo, F. (2022) Characterisation of Biomasses for Their Valorisation in Energy and Biochar Production: Case of Cotton Stalks, Maize Rachis and Rice Husk. Engineering, 14, 173-183. https://doi.org/10.4236/eng.2022.145017
[28]
Villaverde, J., Li, J., Ek, M., Ligero, P. and Vega, A. (2009) Native Lignin Structure of Miscanthus x giganteus and Its Changes during Acetic and Formic Acid Fractionation. Journal of Agricultural and Food Chemistry, 57, 6262-6270. https://doi.org/10.1021/jf900483t
[29]
Cerutti, P.O. and Lescuyer, G. (2011) Le marché domestique du sciage artisanal au Cameroun: État des lieux, Opportunités et défis. Document Occasionnel, Center for International Forestry Research. https://doi.org/10.17528/cifor/003361
[30]
Cheumani, Y.A.M., Ndikontar, M., De Jéso, B. and Sèbe, G. (2011) Probing of Wood-Cement Interactions during Hydration of Wood-Cement Composites by Proton Low-Field NMR Relaxometry. Journal of Materials Science, 46, 1167-1175. https://doi.org/10.1007/s10853-010-4888-3
[31]
Hahladakis, J.N., Velis, C.A., Weber, R., Iacovidou, E. and Purnell, P. (2018) An Overview of Chemical Additives Present in Plastics: Migration, Release, Fate and Environmental Impact during Their Use, Disposal and Recycling. Journal of Hazardous Materials, 344, 179-199. https://doi.org/10.1016/j.jhazmat.2017.10.014
[32]
Tumuluru, J.S. (2016) Effect of Deep Drying and Torrefaction Temperature on Proximate, Ultimate Composition, and Heating Value of 2-mm Lodgepole Pine (Pinus contorta) Grind. Bioengineering, 3, Article 16. https://doi.org/10.3390/bioengineering3020016
[33]
Álvarez, A., Pizarro, C., García, R., Bueno, J.L., and Lavín, A.G. (2016) Determination of Kinetic Parameters for Biomass Combustion. Bioresource Technology, 216, 36-43. https://doi.org/10.1016/j.biortech.2016.05.039
[34]
Wang, Z., Chen, H., Zhu, Z., Xing, S., Wang, S. and Chen, B. (2022) Low-Temperature Straw Biochar: Sustainable Approach for Sustaining Higher Survival of B. megaterium and Managing Phosphorus Deficiency in the Soil. Science of the Total Environment, 830, Article 154790. https://doi.org/10.1016/j.scitotenv.2022.154790
[35]
Gale, M., Nguyen, T., Moreno, M. and Gilliard-AbdulAziz, K.L. (2021) Physiochemical Properties of Biochar and Activated Carbon from Biomass Residue: Influence of Process Conditions to Adsorbent Properties. ACS Omega, 6, 10224-10233. https://doi.org/10.1021/acsomega.1c00530
[36]
Olsson, M. (2006) Wheat Straw and Peat for Fuel Pellets—Organic Compounds from Combustion. Biomass and Bioenergy, 30, 555-564. https://doi.org/10.1016/j.biombioe.2006.01.005
[37]
Örberg, H., Jansson, S., Kalén, G., Thyrel, M. and Xiong, S. (2014) Combustion and Slagging Behavior of Biomass Pellets Using a Burner Cup Developed for Ash-Rich Fuels. Energy & Fuels, 28, 1103-1110. https://doi.org/10.1021/ef402149j
[38]
Holt, G.A., Blodgett, T.L. and Nakayama, F.S. (2006) Physical and Combustion Characteristics of Pellet Fuel from Cotton Gin By-Products Produced by Select Processing Treatments. Industrial Crops and Products, 24, 204-213. https://doi.org/10.1016/j.indcrop.2006.06.005
[39]
Gao, N., Li, A., Quan, C., Du, L. and Duan, Y. (2013) TG-FTIR and Py-GC/MS Analysis on Pyrolysis and Combustion of Pine Sawdust. Journal of Analytical and Applied Pyrolysis, 100, 26-32. https://doi.org/10.1016/j.jaap.2012.11.009
[40]
Tumuluru, J.S., Wright, C.T., Hess, J.R. and Kenney, K.L. (2011) A Review of Biomass Densification Systems to Develop Uniform Feedstock Commodities for Bioenergy Application. Biofuels, Bioproducts and Biorefining, 5, 683-707. https://doi.org/10.1002/bbb.324
[41]
Acda M.N. and Devera, E.E. (2014) Physico-Chemical Properties of Wood Pellets from Forest Residues. Journal of Tropical Forest Science, 26, 589-595.
[42]
Chutturi, M., et al. (2023) A Comprehensive Review of the Synthesis Strategies, Properties, and Applications of Transparent Wood as a Renewable and Sustainable Resource. Science of the Total Environment, 864, Article 161067. https://doi.org/10.1016/j.scitotenv.2022.161067
[43]
Rajput, S.P., Jadhav, S.V. and Thorat, B.N. (2020) Methods to Improve Properties of Fuel Pellets Obtained from Different Biomass Sources: Effect of Biomass Blends and Binders. Fuel Processing Technology, 199, Article ID: 106255. https://doi.org/10.1016/j.fuproc.2019.106255
[44]
Demirbas, A. (2005) Potential Applications of Renewable Energy Sources, Biomass Combustion Problems in Boiler Power Systems and Combustion Related Environmental Issues. Progress in Energy and Combustion Science, 31, 171-192. https://doi.org/10.1016/j.pecs.2005.02.002
[45]
Chen, W.-H., et al. (2020) Novel Renewable Double-Energy System for Activated Biochar Production and Thermoelectric Generation from Waste Heat. Energy Fuels, 34, 3383-3393. https://doi.org/10.1021/acs.energyfuels.9b04495
[46]
McKendry, P. (2002) Energy Production from Biomass (Part 1): Overview of Biomass. Bioresource Technology, 83, 37-46. https://doi.org/10.1016/S0960-8524(01)00118-3
[47]
Parascanu, M.M., Sandoval-Salas, F., Soreanu, G., Valverde, J.L. and Sanchez-Silva, L. (2017) Valorization of Mexican Biomasses through Pyrolysis, Combustion and Gasification Processes. Renewable and Sustainable Energy Reviews, 71, 509-522. https://doi.org/10.1016/j.rser.2016.12.079
[48]
Benyoucef, S. and Harrache, D. (2015) Caractérisation de la microstructure de sciure de bois de pin sylvestre Pinus sylvestris. Journal of Materials and Environmental Science, 6, 765-772.
[49]
Jaouadi, M. (2021) Characterization of Activated Carbon, Wood Sawdust and Their Application for Boron Adsorption from Water. International Wood Products Journal, 12, 22-33. https://doi.org/10.1080/20426445.2020.1785605
[50]
Amara, B., Kocaefe, D., Kocaefe, Y., Bhattacharyay, D., Côté, J. and Gilbert, A. (2022) Effect of Coke Type on Partial Replacement of Coke with Modified Biocoke in Anodes Used in Primary Aluminum Production. In: Eskin, D., Ed., Light Metals 2022, Springer, Cham, 818-825. https://doi.org/10.1007/978-3-030-92529-1_108
[51]
Albashabsheh, N.T. and Heier Stamm, J.L. (2021) Optimization of Lignocellulosic Biomass-to-Biofuel Supply Chains with Densification: Literature Review. Biomass and Bioenergy, 144, Article 105888. https://doi.org/10.1016/j.biombioe.2020.105888
[52]
Chakar, F.S. and Ragauskas, A.J. (2004) Review of Current and Future Softwood Kraft Lignin Process Chemistry. Industrial Crops and Products, 20, 131-141. https://doi.org/10.1016/j.indcrop.2004.04.016
[53]
Hosoya, T., Kawamoto, H. and Saka, S. (2007) Cellulose-Hemicellulose and Cellulose-Lignin Interactions in Wood Pyrolysis at Gasification Temperature. Journal of Analytical and Applied Pyrolysis, 80, 118-125. https://doi.org/10.1016/j.jaap.2007.01.006
[54]
Rutherford, D.W., Wershaw, R.L., Rostad, C.E. and Kelly, C.N. (2012) Effect of Formation Conditions on Biochars: Compositional and Structural Properties of Cellulose, Lignin, and Pine Biochars. Biomass and Bioenergy, 46, 693-701. https://doi.org/10.1016/j.biombioe.2012.06.026
[55]
Börcsök, Z. and Pásztory, Z. (2021) The Role of Lignin in Wood Working Processes Using Elevated Temperatures: An Abbreviated Literature Survey. European Journal of Wood and Wood Products, 79, 511-526. https://doi.org/10.1007/s00107-020-01637-3
[56]
Brosse, N., El-Hage, R., Chaouch, M., Pétrissans, M., Dumarçay, S. and Gérardin, P. (2010) Investigation of the Chemical Modifications of Beech Wood Lignin during Heat Treatment. Polymer Degradation and Stability, 95, 1721-1726. https://doi.org/10.1016/j.polymdegradstab.2010.05.018
[57]
Ragauskas, A.J., et al. (2014) Lignin Valorization: Improving Lignin Processing in the Biorefinery. Science, 344, Article 1246843. https://doi.org/10.1126/science.1246843
[58]
Sablík, P., Giagli, K., Pařil, P., Baar, J. and Rademacher, P. (2016) Impact of Extractive Chemical Compounds from Durable Wood Species on Fungal Decay after Impregnation of Nondurable Wood Species. European Journal of Wood and Wood Products, 74, 231-236. https://doi.org/10.1007/s00107-015-0984-z
[59]
Onuorah, E.O. (2000) The Wood Preservative Potentials of Heartwood Extracts of Milicia Excelsa and Erythrophleum Suaveolens. Bioresource Technology, 75, 171-173. https://doi.org/10.1016/S0960-8524(99)00165-0
[60]
Guedes, R.E., Luna, A.S. and Torres, A.R. (2018) Operating Parameters for Bio-Oil Production in Biomass Pyrolysis: A Review. Journal of Analytical and Applied Pyrolysis, 129, 134-149. https://doi.org/10.1016/j.jaap.2017.11.019
[61]
Al Arni, S. (2018) Comparison of Slow and Fast Pyrolysis for Converting Biomass into Fuel. Renewable Energy, 124, 197-201. https://doi.org/10.1016/j.renene.2017.04.060
[62]
Garcia-Maraver, A., Mata-Sanchez, J., Carpio, M. and Perez-Jimenez, J.A. (2017) Critical Review of Predictive Coefficients for Biomass Ash Deposition Tendency. Journal of the Energy Institute, 90, 214-228. https://doi.org/10.1016/j.joei.2016.02.002
[63]
Babu, B.V. (2008) Biomass Pyrolysis: A State-of-the-Art Review. Biofuels, Bioproducts and Biorefining, 2, 393-414. https://doi.org/10.1002/bbb.92
[64]
Balat, M., Balat, M., Kırtay, E. and Balat, H. (2009) Main Routes for the Thermo-Conversion of Biomass into Fuels and Chemicals. Part 1: Pyrolysis Systems. Energy Conversion and Management, 50, 3147-3157. https://doi.org/10.1016/j.enconman.2009.08.014
[65]
Cong, H., et al.(2018) Slow Pyrolysis Performance and Energy Balance of Corn Stover in Continuous Pyrolysis-Based Poly-Generation Systems. Energy Fuels, 32, 3743-3750 https://doi.org/10.1021/acs.energyfuels.7b03175
