The composite coating has gained wider attention due
to its property to protect materials used in energy, bridges, offshore
platforms, underground pipelines, and the
aviation industry from corrosion and deterioration. In this work, a literature review was conducted about the
processes of nanocomposite coating,
the mechanisms of electrolytic co-deposition, the texture of layers, and the
residual stresses. An important aspect, residual stress, was emphasized, which
represents the persistent stress after removing the external force affecting
a metal in the plastic region. Because it
cannot be measured directly and may be determined by measuring strain and
indirect methods, the sources and methods for measuring residual stresses (XRD,
SEM, TEM, EDS) were described in the last section to provide a
comprehensive overview. Based on the thorough analysis of the published
literature, it was concluded that nanoparticles could be electrodeposited with
Ni on an Al substrate using a direct current and Ni sulfamate as an
electrolytic solution, and Nickel will not reside on the oxide layer covering
Al, so chemical changes are needed to prepare the Al surface. In addition,
texture changes with the thickness of the coated layer must be investigated.
References
[1]
Mei, H.J., et al. (2022) The Additions of V and Cu on the Microstructure and Mechanical Properties of Mo-N Coatings. Coating, 1129, 1-15. https://doi.org/10.3390/coatings12081129
[2]
González-Castillo, E.I., Costantini, T., Shaffer, M.S.P. and Boccaccini, A.R. (2020) Nanocomposite Coatings Obtained by Electrophoretic Co-Deposition of Poly(etheretherketone)/Graphene Oxide Suspensions. Journal of Materials Science, 55, 8881-8899. https://doi.org/10.1007/s10853-020-04632-4
[3]
Maido, M., Lauri, A., Jekaterina, K., Hugo, M., Aivar, T. and Väino, S. (2021) Effective Corrosion Protection of Aluminum Alloy AA2024-T3 with Novel Thin Nanostructured Oxide Coating. Surface and Coatings Technology, 411, Article ID: 126993. https://doi.org/10.1016/j.surfcoat.2021.126993
[4]
Francy, C.G.R., Julieta, T.G. and Juan, M.H.L. (2022) Differences between the Untreated and Treated Diffusion Zone in the Alclad 2024-T3 Aluminum Alloy and Hard Anodic Films. Surface and Coatings Technology, 429, Article ID: 127939. https://doi.org/10.1016/j.surfcoat.2021.127939
[5]
Hirpara, J.G., Chawla, V. and Chandra, R. (2020) Investigation of Tantalum Oxynitride for Hard and Anti-Corrosive Coating Application in Diluted Hydrochloric Acid Solutions. Materials Today Communications, 23, Article ID: 101113. https://doi.org/10.1016/j.mtcomm.2020.101113
[6]
Pinate, S., Ghassemali, E. and Zanella, C. (2022) Strengthening Mechanisms and Wear Behavior of Electrodeposited Ni-SiC Nanocomposite Coatings. Journal of Materials Science, 57, 16632-16648. https://doi.org/10.1007/s10853-022-07655-1
[7]
Herrera-Jimenez, E.J., Bousser, E., Schmitt, T., Klemberg-Sapieha, J.E. and Martinu, L. (2021) Effect of Plasma Interface Treatment on the Microstructure, Residual Stress Profile, and Mechanical Properties of PVD TiN Coatings on Ti-6Al-4V Substrates. Surface and Coatings Technology, 413, Article ID: 127058. https://doi.org/10.1016/j.surfcoat.2021.127058
[8]
Saxena, V., Uma Rani, R. and Sharma, A.K. (2006) Studies on Ultra High Solar Absorber Black Electroless Nickel Coatings on Aluminum Alloys for Space Application. Surface and Coatings Technology, 201, 855-862. https://doi.org/10.1016/j.surfcoat.2005.12.050
[9]
Amina, O., Abudukeremu, K., Raghuveer, S., et al. (2022) A Comprehensive Review on Green Perspectives of Electrocoagulation Integrated with Advanced Processes for Effective Pollutants Removal from Water Environment. Environmental Research, 215, Article ID: 114294. https://doi.org/10.1016/j.envres.2022.114294
[10]
Martina, V., Riccardis, F. and Carbone, D. (2010) A Chemometric Study of Alumina/Peek and Hydroxyapatite/PEEK Suspensions Prepared for Electrophoretic Deposition of Multifunctional Coatings. Advances in Science and Technology, 66, 29-34. https://doi.org/10.4028/www.scientific.net/AST.66.29
[11]
Jothi, K.J. and Palanivelu, K. (2014) Facile Fabrication of Core-Shell Pr6O11-ZnO Modified Silane Coatings for Anti-Corrosion Applications. Applied Surface Science, 288, 60-68. https://doi.org/10.1016/j.apsusc.2013.09.112
[12]
Majdi, M.R., Danaee, I., Seyyed, S. and Seyyed, A. (2017) Preparation and Anti-Corrosive Properties of Cerium Oxide Conversion Coatings on Steel X52. Materials Research, 20, 445-451. https://doi.org/10.1590/1980-5373-mr-2016-0661
[13]
Hee, A.C., Zhao, Y., Jamali, S.S., Bendavid, A., Martin, P.J. and Guo, H. (2019) Characterization of Tantalum and Tantalum Nitride Films on Ti6Al4V Substrate Prepared by Filtered Cathodic Vacuum Arc Deposition for Biomedical Applications. Surface and Coating Technology, 365, 24-32. https://doi.org/10.1016/j.surfcoat.2018.05.007
[14]
Shen, C.W. and Wen, C.J.W. (2003) Kinetics of Electroplating Process of Nano-Sized Ceramic Particle/Ni Composite. Materials Chemistry and Physics, 78, 574-580. https://doi.org/10.1016/S0254-0584(01)00564-8
[15]
Guglielmi, N. (1972) Kinetics of the Deposition of Inert Particles from Electrolytic Baths. Journal of the Electrochemical Society, 119, 1009-1012. https://doi.org/10.1149/1.2404383
[16]
Celis, J.P., Roos, J.R. and Buelens, C. (1987) A Mathematical Model for the Electrolytic Co-Deposition of Particles with a Metallic Matrix. Electrochemical Science and Technology, 134, 1402-1407. https://doi.org/10.1149/1.2100680
[17]
Regis, M., Bellare, A., Pascolini, T. and Bracco, P. (2017) Characterization of Thermally Annealed PEEK and CFR-PEEK Composites: Structure-Properties Relationships. Polymer Degradation and Stability, 136, 121-130. https://doi.org/10.1016/j.polymdegradstab.2016.12.005
[18]
Low, C.T.J., Wills, R.G.A. and Walsh, F.C. (2006) Electrodeposition of Composite Coatings Containing Nanoparticles in a Metal Deposit. Surface and Coatings Technology, 201, 371-383. https://doi.org/10.1016/j.surfcoat.2005.11.123
[19]
González-Castillo, E.I., Žitňan, M., Torres, Y., Shuttleworth, P.S., Galusek, D., Ellis, G. and Boccaccini, A.R. (2022) Relation between Chemical Composition, Morphology, and Microstructure of Poly(ether ether ketone)/Reduced Graphene Oxide Nanocomposite Coatings Obtained by Electrophoretic Deposition. Journal of Material Science, 57, 5839-5854. https://doi.org/10.1007/s10853-022-06995-2
[20]
Jeong, D.H., Gonzalez, F., Palumbo, G., Aust, K.T. and Erb, U. (2001) The Effect of Grain Size on the Wear Properties of Electrodeposited Nanocrystalline Nickel Coatings. Scripta Materialia, 44, 493-499. https://doi.org/10.1016/S1359-6462(00)00625-4
[21]
Radwan, A.B., Sliem, M.H., Yusuf, N.S., Alnuaimi, N.A. and Abdullah, A.M. (2019) Enhancing the Corrosion Resistance of Reinforcing Steel Under Aggressive Operational Conditions Using Behentrimonium Chloride. Scientific Reports, 9, Article No. 18115. https://doi.org/10.1038/s41598-019-54669-y
[22]
Abas, W.A., Rahmati, B., Sarhan, A.D. and Basirun, W.J. (2016) Ceramic Tantalum Oxide Thin Film Coating to Enhance the Corrosion and Wear Characteristics of Ti-6Al-4V Alloy. Journal of Alloys and Compounds, 676, 369-376. https://doi.org/10.1016/j.jallcom.2016.03.188
[23]
Glocker, R. and Kaupp, E. (1924) über die Faserstruktur elektrolytischer Metallniederschläge. Zeitschrift für Physik, 24, 121-139. https://doi.org/10.1007/BF01327239
[24]
Cho, J.Y. and Szpunar, J.A. (2002) The Effect of Substrate Texture and Electroplating Conditions on the Texture and Surface Morphology of Copper Electrodeposits. Materials Science Forum, 408-412, 1609-1614. https://doi.org/10.4028/www.scientific.net/MSF.408-412.1609
[25]
Lu, F., Song, B., He, P., Wang, Z. and Wang, J. (2017) Electrochemical Impedance Spectroscopy (EIS) Study on the Degradation of Acrylic Polyurethane Coatings. RSC Advances, 7, 13742. https://doi.org/10.1039/C6RA26341K https://pubs.rsc.org/en/content/articlelanding/2017/RA/C6RA26341K
[26]
Takada, H., Okada, K., Koga, T. and Hirabayashi, H. (1991) Relation between Preferred Orientation and Young Primes Modulus of Electroplated Nickel. Journal of the Japan Institute of Metals, 55, 12-20. (In Japan) https://doi.org/10.2320/jinstmet1952.55.12_1368
[27]
Pogrebnjak, A., Buranich, V., Ivashchenko, V., Baimoldanov, L., Rokosz, K., Steinar, R., Pawel, Z.O., Bauyrzhan, R., Vyacheslav, B. and Nazgul, E. (2022) The Effect of Substrate Treatment on the Properties of TiAlSiYN/CrN Nanocomposite Coatings. Surfaces and Interfaces, 30, Article ID: 101902. https://doi.org/10.1016/j.surfin.2022.101902
[28]
Alfantazi, A.M., Brehaut, G. and Erb, U. (1997) The Effects of Substrate Material on the Microstructure of Pulse-Plated Zn-Ni Alloys. Surface and Coatings Technology, 89, 239-244. https://doi.org/10.1016/S0257-8972(96)02894-0
[29]
Pangarov, N.A. (1962) The Crystal Orientation of Electrodeposited Metals. Electrochimica Acta, 7, 139-146. https://doi.org/10.1016/0013-4686(62)80023-1
[30]
Pangarov, N.A. and Vitkova, S.D. (1966) Preferred Orientation of Electrodeposited Iron Crystallites. Electrochimica Acta, 11, 1719-1731. https://doi.org/10.1016/0013-4686(66)80085-3
[31]
Evans, D.J. (1958) The Structure of Nickel Electrodeposits in Relation to Some Physical Properties. Transactions of the Faraday Society, 54, 1086-1091. https://doi.org/10.1039/tf9585401086
[32]
Vadim, V., Galina, O., Elena, G., Eduard, A., et al. (2016) Development of Complete Color Palette Based on Spectrophotometric Measurements of Steel Oxidation Results for Enhancement of Color Laser Marking Technology. Materials & Design, 89, 684-688. https://doi.org/10.1016/j.matdes.2015.10.030
[33]
Sheikh, A.F., Ankush, R., Sanjay, M., Ramachandra, A.S., Subramanian, J. and Mir, I.H. (2022) Nanostructured Coatings: Review on Processing Techniques, Corrosion Behaviour and Tribological Performance. Nanomaterials, 12, 1323. https://doi.org/10.3390/nano12081323
[34]
Czerwinski, F. and Szpunar, J.A. (1999) Controlling the Surface Texture of Nickel for High Temperature Oxidation Inhibition. Corrosion Science, 41, 729-740. https://doi.org/10.1016/S0010-938X(98)00146-2
[35]
BinSabt, M.H., Abditon, M. and Galal, A. (2022) Highly Efficient Nanocomposite-Containing Coatings for the Protection of Mg Alloy against Corrosion in Chloride Containing Electrolytes. Applied Physics A, 128, 151-162. https://doi.org/10.1007/s00339-021-05248-4
[36]
Lingois, P., Berglund, L., Greco, A. and Maffezoli, A. (2003) Chemically Induced Residual Stresses in Dental Composites. Journal of Materials Science, 38, 1321-1331. https://doi.org/10.1023/A:1022811315807
[37]
Liu, X. and Zhang B. (2002) Effects of Grinding Process on Residual Stresses in Nanostructured Ceramic Coatings. Journal of Materials Science, 37, 3229-3239. https://doi.org/10.1023/A:1016174731658
[38]
Buchmann, M., Gadow, R. and Tabellion, J. (2000) Experimental and Numerical Residual Stress Analysis of Layer Coated Composites. Materials Science and Engineering: A, 288, 154-159. https://doi.org/10.1016/S0921-5093(00)00862-5
[39]
Jian, M.Z., Ke, W.X. and Vincent, J. (2001) Dependence of Stresses on Grain Orientations in Thin Polycrystalline Films on Substrates: An Explanation of the Relationship between Preferred Orientations and Stresses. Applied Surface Science, 180, 1-5. https://doi.org/10.1016/S0169-4332(01)00243-4
[40]
Jignesh, H., Vipin, C. and Ramesh, C. (2021) Anticorrosive Behavior Enhancement of Stainless Steel 304 through Tantalum-Based Coatings: Role of Coating Morphology. Journal of Materials Engineering and Performance, 30, 1895-1905. https://doi.org/10.1007/s11665-021-05542-5
[41]
Mimani, T. and Patil, K.C. (2001) Solution Combustion Synthesis of Nanoscale Oxides and Their Composites. Materials Physics and Mechanics, 4, 134-137. https://mpm.spbstu.ru/article/2001.6.14/ https://doi.org/10.1016/S0894-7317(01)70064-8
[42]
Ashish, K.K., Muhammad, U.B., Zulfiqar, A.K. and Pradeep, L.M. (2020) Corrosion Performance of Nanocomposite Coatings in Moist SO2 Environment. The International Journal of Advanced Manufacturing Technology, 106, 4769-4776. https://doi.org/10.1007/s00170-020-04949-z
[43]
Seyedeh, P.M., Abudukeremu, K., Raghuveer, S., Razieh, A., Maryam, S., Jun, L., Nur, S.Z. and Farooq, S. (2022) Superior Removal of Humic Acid from Aqueous Stream Using Novel Calf Bones Charcoal Nanoadsorbent in a Reversible Process. Chemosphere, 301, Article ID: 134673. https://doi.org/10.1016/j.chemosphere.2022.134673
